Penco Products, Inc.
Subsidiary of Vesper Corporation
P.O. Box 158
Skippack, PA 19474
Phone: (610) 666-0500
Fax: (610) 666-7561
E-mail: general@pencoproducts.com
Website: http://www.pencoproducts.com
Steel Lockers - 10500
Vanguard Lockers With Recessed Pocket Overview
This locker is the same design as the standard Vanguard, with the
exception that the die cast handle is replaced with a deep drawn stainless
steel Classic III recessed pocket. Available as one, two or three
tier, plus Two Person and Duplex lockers.
VANGUARD WITH RECESSED POCKET LOCKER SPECIFICATIONS
MATERIALS
SHEET STEEL: All parts made from prime grade mild cold
rolled sheet steel free from surface imperfection, and capable of taking
a high grade enamel finish.
HINGES: .074" thick, 2" high, double spun, full loop, tight
pin, five-knuckle hinges, projection welded to door frame and securely
fastened to the door with 2 steel rivets. Doors over 42" high shall
have three hinges; all other doors shall have two hinges.
FINISHING: Chemically pretreat metal with a six stage cleaning
phosphatizing and metal preparation process. Finish coat shall be
hot airless electrostatically applied enamel baked on at 350 to 400 degrees.
Select colors from manufacturer's minimum standard 20 colors. All
lockers shall be painted inside and outside with the same color.
EQUIPMENT: Coat hooks and coat rods are zinc plated.
Truss fin head bolts and hex nuts are zinc coated.
FABRICATION GENERAL
CONSTRUCTION: Built on the unit principle—each locker shall
have an individual door and frame, individual top, bottom, back and shelves
with common intermediate uprights separating compartments. Lockers
shall be fabricated square, rigid and without warp. Doors shall be
flat and free of distortion.
DOOR FRAME: All door frame members to be not less than
16 gauge formed to a channel shape. Vertical members to have an additional
flange to provide a continuous door strike. Intermembering parts
to be mortised and tenoned and electrically welded together in a rigid
assembly capable of resisting strains.
Cross frame members of 16 gauge channel shapes including intermediate
cross frame on double and triple tier lockers shall be securely welded
to vertical framing members to ensure rigidity.
BODY: Bolt spacing in locker body construction not to exceed
9" o.c. All locker body components shall be made of cold rolled steel
specially formed for added strength and rigidity and to ensure tight joints
at fastening points. Tops & bottoms shall be 24 gauge with three
sides formed 90 degrees and the front offset formed to be flush with the
horizontal frame member. Shelves shall be 24 gauge with four sides
formed to 90 degrees, the front edge shall have a second bend. Backs
& sides shall be 24 gauge.
DOORS: Doors 30" or higher shall be formed from one piece
16 gauge cold rolled sheet steel. Doors less than 12" wide shall
be 18 gauge. Formations shall consist of a full channel shape on
the lock side of adequate depth to fully conceal the lock bar, channel
formation on the hinge side, and right angle formations across the top
and bottom. Doors over 15" wide x 60" or 72" high shall have a 3"
wide 20 gauge full height reinforcing pan welded to the inside face of
the door on 6" centers.
DOOR HANDLE & LATCHING; 1, 2 & 3 TIER, TWO PERSON & DUPLEX:
Provide handles recessed in the door with finger lift control. 20
gauge drawn pocket shall be brushed stainless steel securely fastened to
the door with two tabs plus a positive tamper resistant decorative fastener.
The pocket shall be of sufficient depth to prevent a combination padlock,
built-in combination lock or key lock from protruding beyond the face of
the door. A lock hole cover plate shall be provided for use with
padlocks.
The lifting piece shall be 14 gauge formed steel, attached to the latching
channel with one concealed retaining lug and one rivet assuring a positive
two point connection. Handle finger lift shall have a padlock eye
for use with a 9/32" diameter padlock shackle. It shall have a sound
deadening molded comfortable finger lift attached with a rivet.
Doors to have latch clip engaging the door frame at three points on
doors over 42" high and two points on all other doors. Locking device
to be positive, automatic type, whereby locker door may be locked when
open, then closed without unlocking. One rubber silencer shall be
firmly secured in the frame at each heavy gauge latch hook. Latch
clips shall be glass filled nylon for long life and low friction and shall
hold doors shut by engaging the latch hooks. The latch channel assembly
shall be quieted by the use of unique nylon glides to reduce noise.
VENTILATION: Lockers with doors 72” to 36” high shall have
two sets of louvers, one set near the top of the door and another set near
the bottom of the door. Lockers with doors 30” or less in height,
shall have a minimum of one set of louvers.
NUMBER PLATES: Each locker to be supplied with a polished
aluminum number plate, 2-1/4" wide x 1" high, with black numerals not less
than 3/8" high. Number plates shall be attached to the face of the
door with two aluminum rivets.
INTERIOR EQUIPMENT: Single-tier lockers 60" or higher shall
have a hat shelf located approximately 9" below the top of locker; if less
than 18" deep, locker shall have three single-prong hooks and one double-prong
ceiling hook. Single tier lockers 18" or more in depth shall have
a coat rod instead of a ceiling hook. 30" & 36" high lockers
shall have three single-prong wall hooks and one double-prong ceiling hook.
Hooks to be attached with two bolts per hook. 20" & 24" high
lockers to have three wall hooks for 12" wide, and four wall hooks for
15" wide and wider.
LOCKER ACCESSORIES
See locker Accessory Specifications.
OPTIONS
BODY: Locker shall be assembled using rivets.
SIDE AND BACK VENTILATION: Sides and/or backs shall be
perforated with 1/2" diameter holes in patterns of 42 holes per group.
DOOR VENTILATION:
Visual perforations shall consist of 5/8" wide x 1-1/8" high rectangular
perforations in the door in standard manufacturer's patterns. Doors
with visual perforations shall not have louvers.
Mini louvers shall be 5/8" wide x 1/4" high and be placed in doors in
manufacturer's standard pattern. Doors with mini louvers shall not
have standard louvers.
A. D. A. COMPLIANT LOCKERS: Handicap lockers
shall have recessed handles and shall be single tier or the lower opening
of a double tier locker. Locker bottom shall be a minimum of 9" off
the floor, or an extra shelf placed 9" off the floor. Single tier
lockers shall have a shelf 48" off the floor. Doors assigned for
handicapped use shall have an appropriate symbol sign.
EXECUTION
INSTALLATION: Install metal lockers at location shown in
accordance with manufacturer's instructions for plumb, level, and flush
installation.
ANCHOR LOCKERS to the floor and wall 48" on center or less as
recommended by the manufacturer.
INSTALL SLOPING HOODS AND METAL FILLERS using concealed fasteners.
Provide flush hairline joints against adjacent surfaces.
INSTALL BENCHES by fastening bench tops to pedestals and securely
anchoring to the floor using appropriate anchors for the floor material.
ADJUST & CLEAN: Adjust doors and latches to operate
without binding. Verify that latches are operating satisfactorily.
TOUCH UP marred finishes with factory supplied paint.
ACCEPTABLE MANUFACTURERS
1. Penco Products, Inc., Oaks, PA—Vanguard Recessed Pocket Lockers
PENCO RESERVES THE RIGHT TO VARY SPECIFICATIONS CONSISTENT WITH ITS
POLICY OF CONTINUOUS PRODUCT IMPROVEMENT.
|