Penco Products, Inc.
Subsidiary of Vesper Corporation
P.O. Box 158
Skippack, PA 19474
Phone: (610) 666-0500
Fax: (610) 666-7561
E-mail: general@pencoproducts.com
Website: http://www.pencoproducts.com
Lockers – 10500
All-Welded Locker Overview
Penco All-Welded lockers are shipped completely assembled.
All components are welded together at the factory prior to being painted
with a durable baked-on enamel finish. Doors have a full-length continuous
hinge. Locker groups up to 54" wide can be shipped as units, reducing on
site installation time to a minimum.
PENCO ALL-WELDED LOCKER SPECIFICATIONS
MATERIALS
SHEET STEEL: All parts made from prime grade mild cold
rolled sheet steel free from surface imperfection, and capable of taking
a high grade enamel finish.
FINISHING: Chemically pretreat metal with a six stage cleaning
phosphatizing and metal preparation process. Finish coat shall be
hot airless electrostatically applied enamel baked on at 350 to 400 degrees.
Select colors from manufacturer’s minimum standard 20 colors. All
lockers shall be painted inside and outside with the same color.
FABRICATION GENERAL
CONSTRUCTION: Fabricate lockers square, rigid and without
warp. Metal faces shall be flat and free of distortion. Lockers
shall be pre-assembled of welded construction, all welds shall be free
of burrs. Grouping shall be the most practical that conforms to the
job requirement. No bolts, nuts or rivets shall be allowed in the
assembly of main locker groups. Each locker group shall be securely
welded into a one piece structure.
SIDE & DOOR FRAME: Shall be manufactured from 16 gauge.
The front edge of the frame shall be formed to a channel shape with a continuous
door strike. Two and three tier lockers shall have intermediate 16
gauge channel shaped horizontal frame members attached to the side frames
with mortise and tenon construction, and securely welded. Intermediate
frames shall consist of two 16 gauge frame channels securely welded together.
TOPS: Shall be 16 gauge notched and formed. Each group
of lockers shall have one continuous flat top.
BOTTOMS: Shall be 16 gauge notched and formed. Each group
of lockers shall have one continuous bottom suitable for anchoring to wood
or concrete bases.
SHELVES: Shall be 16 gauge, flanged on four sides with an additional
return flange on the front edge to increase strength.
BACKS: Shall be solid 18 gauge cold rolled steel. One piece
steel backs for groups to 48" wide. Groups over 48" wide shall have
two piece backs.
DOORS: Doors 20" or higher shall be formed from one piece 14
gauge cold rolled sheet steel. Formations shall consist of a full
channel shape on the lock side of adequate depth to fully conceal the lock
bar, channel formation on the hinge side, and right angle formations across
the top and bottom. Doors over 15" wide and over 30" high shall have
a 3" wide 20 gauge full height heavy duty reinforcing pan welded to the
inside face of the door on 6" centers.
Doors for box lockers 4, 5, 6, 8 & 9 tiers high shall be 14 gauge
steel and have channel formations on lock side and hinge side and have
right angle flanges on the top and bottom.
DOOR HANDLE & LATCHING 1, 2 & 3 TIER: Handles shall
be recessed in the door and be finger lift control. The 20 gauge
drawn pocket shall be brushed stainless steel securely fastened to the
door with two tabs plus a positive tamper resistant decorative fastener.
The pocket shall be of sufficient depth to prevent a combination padlock,
built-in combination lock or key lock from protruding beyond the face of
the door. A lock hole cover plate shall be provided for use with
padlocks.
The lifting piece shall be 14 gauge formed steel, attached to the latching
channel with one concealed retaining lug and one rivet assuring a positive
two point connection. Handle finger lift shall have a padlock eye
for use with a 9/32" diameter padlock shackle. It shall have a sound
deadening molded comfortable finger lift attached with a rivet.
Doors to have latch clip engaging the door frame at three points on
60" & 72" high and two points on 20" through 36" high doors.
Locking device to be positive, automatic type, whereby locker door may
be locked when open, then closed without unlocking. One rubber silencer
shall be firmly secured in the frame at each heavy gauge latch hook.
Latch clips shall be glass filled nylon for long life and low friction
and shall hold doors shut by engaging the latch hooks. Latch hooks
on diamond-perforated lockers shall have tamper guards.
DOOR HANDLE & LATCHING 4 TO 9 TIER BOX LOCKERS: Doors
shall be punched for use with padlocks or built-in locks. Doors for
use with padlocks shall be equipped with an 18 gauge combination door pull,
staple and lock hole cover plate with integral friction catch.
VENTILATION: All sides and doors 20" or higher shall be
perforated with diamond-shaped openings 3/4" wide x 1-1/2" high in a quantity
and pattern to ensure maximum ventilation and maintain structural strength.
All other doors shall have small diamond-shaped perforations 7/16" wide
x 15/16" high.
NUMBER PLATES: Each locker door to be supplied with a polished
aluminum number plate, 2-1/4" wide x 1" high, with black numerals not less
than 3/8" high. Number plates shall be attached to the face of the door
with two aluminum rivets.
HINGES: 16 gauge continuous type hinge riveted to the frame and
the door for the full height of the door.
INTERIOR EQUIPMENT: Single tier lockers 60" or higher shall
have one hat shelf located approximately 9" down from the top of the locker.
Lockers 20" or more in height and 12" or 15" wide shall have one double
prong ceiling hook and two single prong wall hooks. Lockers over
15" wide shall have a double prong ceiling hook and four single prong wall
hooks. All coat hooks shall be forged steel with ball ends, zinc
plated.
LOCKER ACCESSORIES
Lockers shall be furnished with the accessories selected from the list
below:
Continuous metal base: If required base shall be 4" high,
16 gauge, integral with locker bottom.
Legs: If required, each group of lockers shall be furnished
with four legs each 4" high, 14 gauge and welded to the locker bottom.
For additional accessories see Accessory Specifications.
OPTIONS
DOORS: Box locker doors 4 to 9 tier, as an alternative
option each door shall be furnished with a stainless steel padlock strike.
DOOR HANDLE & LATCHING 4 TO 9 TIER BOX LOCKERS: As
an alternate option, each door shall be provided with a finger operated
11 gauge slam latch with an electrogalvanized trigger, and a spring contained
in a 14 gauge case welded to the door. The spring latch engages a
13 gauge hasp welded to the frame. Rubber bumpers shall be securely
installed in the frame.
VENTILATION: If specified, all perforations may be deleted.
If deleted, louvers may be added to the doors.
DOOR VENTILATION: Delete diamond perforations in the doors
and substitute with standard louvers, or mini louvers may be substituted
and shall be 5/8" wide x 1/4" high. Louvers shall be placed in doors
in manufacturer's standard pattern.
A.D.A. COMPLIANT LOCKERS: Handicap lockers shall have recessed
handles and shall be single tier or the lower opening of a double tier
locker. Locker bottom shall be a minimum of 9" off the floor, or
an extra shelf placed 9" off the floor. Single tier lockers shall
have a shelf 48" off the floor. Doors assigned for handicapped use
shall have an appropriate symbol sign.
EXECUTION
INSTALLATION: Install metal lockers at location shown in
accordance with manufacturers instructions for plumb, level, and flush
installation.
ANCHOR LOCKERS to the floor and wall 48" on center or less as
recommended by the manufacturer.
INSTALL SLOPING HOODS AND METAL FILLERS using concealed fasteners.
Provide flush hairline joints against adjacent surfaces.
INSTALL BENCHES by fastening bench tops to pedestals and securely
anchoring to the floor using appropriate anchors for the floor material.
ADJUST & CLEAN: Adjust doors and latches to operate
without binding. Verify that latches are operating satisfactorily.
TOUCH UP marred finishes with factory supplied paint.
ACCEPTABLE MANUFACTURERS
1. Penco Products, Inc., Oaks, PA—All-Welded Lockers
PENCO RESERVES THE RIGHT TO VARY SPECIFICATIONS CONSISTENT WITH ITS
POLICY OF CONTINUOUS PRODUCT IMPROVEMENT.
|