Penco Products, Inc.
Subsidiary of Vesper Corporation
P.O. Box 158
Skippack, PA 19474
Phone: (610) 666-0500
Fax: (610) 666-7561
E-mail: general@pencoproducts.com
Website: http://www.pencoproducts.com
Lockers – 10500
Guardian Defiant Single Point Latch (SPL) Locker Overview
Available in 1, 2 and 3 tier models. Same as the Guardian Standard
Lockers except that these lockers have a 14 gauge one piece door with integral
box beam stiffening reinforcements on the hinge and latch sides and a full
length continuous hinge. For ease of maintenance, there are no moving
latch parts. Stainless steel recessed pocket has integral finger
grip door pull. Accepts built-in locks or padlocks.
GUARDIAN DEFIANT SINGLE POINT LATCH (SPL) LOCKER SPECIFICATIONS
MATERIALS
SHEET STEEL: All parts made from prime grade mild cold
rolled sheet steel free from surface imperfection, and capable of taking
a high grade enamel finish.
HINGES: 16 gauge continuous type hinge riveted to the frame and
the door for the full height of the door.
FINISHING: Chemically pretreat metal with a six stage cleaning
phosphatizing and metal preparation process. Finish coat shall be
hot airless electrostatically applied enamel baked on at 350 to 400 degrees.
Select colors from manufacturer's minimum standard 20 colors. All
lockers shall be painted inside and outside with the same color.
EQUIPMENT: Coat hooks and coat rods are zinc plated.
Truss fin head bolts and hex nuts are zinc plated.
FABRICATION GENERAL
CONSTRUCTION: Built on the unit principle—each locker shall
have an individual door and frame, individual top, bottom, back and shelves
with common intermediate uprights separating compartments. Lockers
shall be fabricated square, rigid and without warp. Doors shall be
flat and free of distortion.
DOOR FRAME: All door frame members to be not less than
16 gauge formed to a channel shape. Vertical members to have an additional
flange to provide a continuous door strike. Intermembering parts
to be mortised and tenoned and electrically welded together in a rigid
assembly capable of resisting strains.
Cross frame members of 16 gauge channel shapes including intermediate
cross frame on double and triple tier lockers shall be securely welded
to vertical framing members to ensure rigidity.
BODY: Bolt spacing in locker body construction not to exceed
9" o.c. All locker body components shall be made of cold rolled steel
specially formed for added strength and rigidity and to ensure tight joints
at fastening points. Tops & bottoms shall be 24 gauge with three
sides formed 90 degrees and the front offset formed to be flush with the
horizontal frame member. Shelves shall be 24 gauge with four sides
formed to 90 degrees, the front edge shall have a second bend. Backs
& sides shall be 24 gauge.
DOORS: Doors 20" or higher shall be formed from one piece
14 gauge steel. Formations shall be box formed stiffeners on the
hinge side and latch side. Both formations shall have a 1/2" flange
spot welded to the inside face of the door on 4-1/2" centers. Top
and bottom flanges shall have one 90 degree bend. For long life,
the door shall be manufactured from one integral piece. Door shall
be manufactured to allow maximum ventilation and stiffness.
DOOR HANDLE & LATCHING 1, 2 & 3 TIER: Handles shall
be recessed in the door. The formed pocket shall be brushed stainless
steel securely fastened to the door with two lugs plus a positive tamper
resistant fastener. The pocket shall be of sufficient depth to prevent
a combination padlock, built-in combination lock or key lock from protruding
beyond the face of the door. A lock hole cover plate shall be provided
for use with padlocks. All pockets shall be 20 gauge drawn steel
for superior strength. Door pull shall be formed in the pocket.
Pocket and pull shall be integral.
Doors shall have a catch to retain unlocked doors in the closed position.
Locking shall be accomplished by an 11 gauge lug welded to the locker frame.
The lug shall include a surface for the bolt of a built-in combination
or key lock to engage. A padlock staple shall protrude through the
20 gauge pocket. The lug shall include an anti-pry flange and notch
to deter prying open when locked. Rubber door silencers shall be
firmly attached to the locker frame.
VENTILATION: Shall be facilitated by air flow slots located
in the top & bottom flange of the door. The door front shall
be flush with no exposed louvers.
NUMBER PLATES: Each locker door to be supplied with a polished
aluminum number plate, 2-1/4" wide x 1" high, with black numerals not less
than 3/8" high. Number plates shall be attached to the face of the door
with two aluminum rivets.
INTERIOR EQUIPMENT: Single tier lockers 60" or higher shall
have a hat shelf located approximately 9" below the top of locker; if less
than 18" deep, locker shall have three single-prong hooks and one double-prong
ceiling hook. Single tier lockers 18" or more in depth shall have
a coat rod instead of a ceiling hook. 30" & 36" high lockers
shall have three single-prong wall hooks and one double-prong ceiling hook.
Hooks to be steel, ball tip zinc plated, attached with two bolts per hook.
20" & 24" high lockers to have three wall hooks for 12" wide and four
wall hooks for 15" and wider.
LOCKER ACCESSORIES: Lockers shall be furnished with the
accessories selected from the Accessory Specifications.
OPTIONS
BODY: Lockers shall be assembled using rivets.
DOOR VENTILATION: Mini louvers shall be 5/8" wide x 1/4"
high and be placed in doors in manufacturer’s standard pattern.
EXECUTION
INSTALLATION: Install metal lockers at location shown in
accordance with manufacturer's instructions for plumb, level, and flush
installation.
ANCHOR LOCKERS to the floor and wall 48" on center or less as
recommended by the manufacturer.
INSTALL SLOPING HOODS AND METAL FILLERS using concealed fasteners.
Provide flush hairline joints against adjacent surfaces.
INSTALL BENCHES by fastening bench tops to pedestals and securely
anchoring to the floor using appropriate anchors for the floor material.
ADJUST & CLEAN: Adjust doors and latches to operate
without binding. Verify that latches are operating satisfactorily.
TOUCH UP marred finishes with factory supplied paint.
ACCEPTABLE MANUFACTURERS
1. Penco Products, Inc., Oaks, PA—Guardian Defiant (SPL) Lockers
PENCO RESERVES THE RIGHT TO VARY SPECIFICATIONS CONSISTENT WITH ITS
POLICY OF CONTINUOUS PRODUCT IMPROVEMENT.
|