The McGraw-Hill Companies
McGraw Hill Construction - Building Materials, Products and Manufacturers
home |
product centers
| find a rep |
utilities
| education | project network | SNAP Reader Service | forums
register | forgot password | remember me | help
 
MasterFormat 2004   help
 
Product Center Image
 |   |   | 


LATICRETE INTERNATIONAL, INC.
1 LATICRETE Park North
Bethany, CT 06524-3423 USA
Tel: (203) 393-0010
Toll-Free: (800) 243-4788
Fax: (203) 393-1684
E-mail: technicalservices@laticrete.com
Web site: http://www.laticrete.com


LATICRETE® PermaColor Grout

PRODUCT DESCRIPTION

LATICRETE PermaColor Grout is a high performance grout that provides a grout joint that is dense, hard and will resist cracking. LATICRETE PermaColor Grout is color consistent. Mix only with water.

Advantages
  • Consistent Color
  • Mixes with water only
  • Ideal for floors and walls ( Joint Widths of 1/16-1/2" [1.5 to 12 mm])
  • Inhibits Mold and Mildew with Microban®
  • Component of LATICRETE 15 Year Residential Warranty (see DS 230.14)
  • Improved Stain Resistance For a Cement Based Grout
  • Interior and Exterior Applications
  • Residential and Commercial
Packaging

25 lb (11.3 kg) bags
8 lb (3.6 kg) cartons

Shelf Life

Factory sealed containers of this product are guaranteed to be of first quality for the time period listed below if stored off the ground in a dry area.

25 lb (11.3 kg) bags – one (1) year
8 lb (3.6 kg) cartons – two (2) years

Limitations
  • Adhesives/mastics, mortars and grouts for ceramic tile, pavers, brick and stone are not replacements for waterproofing membranes. When a waterproofing membrane is required, use a LATICRETE Waterproofing Membrane (see Section 10 FILING SYSTEM).
  • Note: Surfaces must be structurally sound, stable and rigid enough to support ceramic/stone tile, thin brick and similar finishes. Substrate deflection under all live, dead and impact loads, including concentrated loads, must not exceed L/360 for thin bed ceramic tile/brick installations or L/480 for thin bed stone installations where L=span length.
  • DO NOT use for chemical resistance. Use LATAPOXY® 2000 Industrial Grout when chemical resistance is required.
  • DO NOT use acid to clean colored grout joints.
  • Job site conditions will affect the final color of colored grouts. Try a small test area to determine your results before grouting the entire installation.
  • Certain types of tile are more absorbent than others and will trap color pigment during grouting. Prior to grouting, test for absorption of color pigment. Porous tiles will need to be sealed prior to grouting.
  • Selecting Other Grouting Materials: LATICRETE has grouting materials designed for every use. For installations that require high strength and chemical resistance choose LATAPOXY 2000 Industrial Grout. This product is ideal for installations where a stain resistant colorfast grout is desired.
Cautions

Consult MSDS for more safety information.

  • During cold weather, protect finished work from traffic until fully cured.
  • Contains portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.
  • Do not take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas.
  • Grout may scratch soft glazed or polished surfaces. Conduct a test area to verify results.
  • In submerged applications or steam rooms allow LATICRETE PermaColor Grout to cure for 14 days at 70°F (21°C) before use of area. See TDS 192 for more information on these applications.
  • Keep out of reach of children.
TECHNICAL DATA

Applicable Standards

(ANSI A118.6 and A118.7)

Physical Properties

Tensile Strength (28 Day)
510 psi (3.5 MPa)
Compressive Strength
4500 psi (31.0 MPa)
Flexural Strength
1250 psi (8.62 MPa)
Linear Shrinkage (7 day)
0.0450%

Working Properties

Pot Life
40-60 min at 70°F (21°C)
Final Set
3 hrs
Heavy Foot Traffic
6 hrs

Specifications subject to change without notification. Results shown are typical but reflect test procedures used. Actual field performance will depend on installation methods and site conditions.

INSTALLATION

Surface Preparation

Before starting to grout remove spacers and debris in grout joints and remove dust and dirt using a wet sponge. Do not leave water standing in joints. Substrate temperature must be between 40°F (4°C) and 90°F (32°C). Apply grout release or sealer if necessary. Refer to LATICRETE® Grout Troubleshooting Guide for more information on grouting.

Mixing

Use approximately 2 quarts (1.9 l) of clean potable water for 25 lbs (11.3 kg) of LATICRETE PermaColor Grout. No additive required. Do not use with LATICRETE 1776 Grout Enhancer or any other latex additive. Place water in a clean mixing container and add grout powder. Mix with a slow speed drill mixer (300 rpm) for 1 minute. Wait for 5 minutes and remix with drill for 1 minute.

Application

Clean tile surface with a damp sponge. Spread with a sharp, firm rubber grout float or wall float for narrow wall joints. To remove excess grout hold the float at a 90° angle and pull it at a 45° angle diagonally across the joints to avoid pulling out the material.

Note: If the grout begins to stiffen during installation, remix with drill mixer for 10-15 seconds. DO NOT ADD MORE WATER!

Cleaning

Wait 15-20 minutes at 70°F (21°C). For wider joints or cooler temperatures wait longer (25-30 minutes) Begin initial cleaning by lightly wiping down entire area to be cleaned with a damp sponge. Wash with a damp sponge (not wet). Work diagonally to the joints. Allow to dry 3 hours at 70°F (21°C). For second cleaning use a damp sponge or dry cloth to remove remaining grout haze.

Note: Use caution when polishing soft glazed tiles or polished stone.

If grout is to be sealed, LATICRETE generally recommends waiting a minimum of a 48 hours at 70°F (21°C) prior to sealing LATICRETE PermaColor Grout, or any other cement-based LATICRETE grout; however, we suggest deferring to the written recommendations of the sealer manufacturer to make the final determination, as certain sealers may require the cement grout to cure for an extended period of time.


AVAILABILITY AND COST

Availability

LATICRETE and LATAPOXY® materials are available worldwide.

For Distributor information:
Toll Free: 1.800.243.4788
Telephone: +1.203.393.0010

For on-line distributor information, visit LATICRETE at www.laticrete.com.

Cost

Contact a LATICRETE Distributor in your area.

WARRANTY

See 10. FILING SYSTEM:
DS 230.13: LATICRETE Product Warranty

A component of:
DS 230.12: LATICRETE 10 Year System Warranty
DS 230.14: LATICRETE 15 Year Residential Warranty

MAINTENANCE

LATICRETE and LATAPOXY grouts require routine cleaning with a neutral pH soap and water. All other LATICRETE and LATAPOXY materials require no maintenance but installation performance and durability may depend on properly maintaining products supplied by other manufacturers.

TECHNICAL SERVICES

Technical assistance

Information is available by calling the LATICRETE Technical Service Hotline (hours 8:00 AM to 5:30 PM EST):
Toll Free: 1.800.243.4788, ext. 235
Telephone: +1.203.393.0010, ext. 235
Fax: +1.203.393.1948

Technical and safety literature

To acquire technical and safety literature, please visit our website at www.laticrete.com.

FILING SYSTEM

Additional product information is available on our website at www.laticrete.com. The following is a list of related documents:
DS 230.13: LATICRETE Product Warranty
DS 230.12: LATICRETE 10 Year System Warranty
DS 230.14: LATICRETE 15 Year Residential Warranty
DS 236.0: LATICRETE 9235 Waterproofing Membrane



 |   |   |