DOVETAIL AND CHANNEL SLOT ANCHORING SYSTEMS
DOVETAIL ANCHOR SLOT SYSTEM: Use dovetail
anchor slots in new concrete structures and walls and in precast concrete.
Slots are nailed to the concrete form before pouring concrete using each
indented nail hole provided in the bottom of the dovetail channel. Slots
are provided with foam filler to prevent concrete from entering the slot
during the pour. Dovetail slots are typically installed vertically and
spaced 16" (406 mm) to 24" (610 mm) o.c. Standard length is 10 ft. (3.048
m)
No. 100 STANDARD DOVETAIL SLOT: 1" (25.4 mm) wide x 1" (25.4
mm) deep x 5/8" (15.9 mm) throat, nail holes provided 4" (102 mm) o.c.
Available in 26, 24, 22, and 20 gage Mill Galvanized Steel and Stainless
Steel.
No. 100-A LARGE DOVETAIL SLOT: 2" (51 mm) wide x 1-1/2" (38 mm)
deep x 1-3/8" (35 mm) throat, nail holes 12" (305 mm) o.c. Available 20,
18, or 16 gage mill galvanized and 18 or 16 gage stainless steel. Use with
2" (51 mm) wide anchors; add suffix "A" to anchor catalog number.
No. 100-B SHALLOW DOVETAIL SLOT: 7/8" (22 mm) wide x 1/2"
(12.7 mm) deep x 5/8" (15.9 mm) throat, nail holes 12" (305 mm) o.c. in
20 gage mill galvanized or stainless steel. Use with 1" (25.4 mm) wide
anchors; add suffix "B" to anchor catalog number.
TO SPECIFY DOVETAIL ANCHORS:
THICKNESS: 16 gage, 12 gage, 1/8" (3.1 mm), and 3/16" (4.7 mm)
thick.
LENGTH: Measured from face of concrete.
WIDTH: Standard and Type B Dovetail anchors are typically 1"
(25.4 mm) wide and Type A Dovetail Anchors are 2" (51 mm) wide. Add an
"A" or "B" suffix to catalog number to specify anchors for type "A" or
"B" Dovetail Slot.
MATERIALS: Available in mill galvanized, stainless steel, or
hot dipped galvanized.
DOVETAIL ANCHORS
103 DOVETAIL TRIANGLE TIE: 12 gage clip factory assembled to
a No. 316 Triangle tie 3/16 inch (4.76 mm) diameter x [tie length]
104 DOVETAIL PARTITION ANCHOR: [gage] x [width] x [length from
face of concrete]
105 DOVETAIL STANDARD BRICK ANCHOR: [gage] x 1 inch (25 mm) wide
x 3-1/2 inch (89 mm) long.
106 DOVETAIL CORRUGATED ANCHOR: [gage] x 1 inch (25 mm) wide
x [length from face of concrete]
107 DOVETAIL WIRE BRICK ANCHOR: 1/8 inch (3.17 mm) thick anchor
furnished loose with No. 316 Triangle Tie 3/16 inch (4.76 mm) diameter
x [tie length]
108 DOVETAIL CAVITY WALL ANCHOR: [gage] x [width] x [length from
face of concrete]
109 DOVETAIL FLAT ANCHOR: [gage] x [width] x [length from face
of concrete]
110 DOVETAIL FURRING ANCHOR: [gage] x [width] x 1-1/2 inches
(38.1 mm) long from face of concrete.
115 DOVETAIL STONE ANCHOR: [gage] x [width] x [length from face
of concrete] x [i.d. bend length]
116 DOVETAIL SPLIT END ANCHOR: [gage] x [width] x [length from
face of concrete] x [i.d. split-bend length].
117 DOVETAIL SPLIT BEND ANCHOR: [gage] x [width] x [length from
face of concrete] x [i.d. split-bend length]
118 DOVETAIL STONE PIN ANCHOR: [gage] x [width] x [length from
face of concrete] with [welded][fixed][loose] pin [diameter] x [length]
centered [length] from end of anchor
121 DOVETAIL THREADED ROD ANCHOR: [gage] x [width] x [overall
length from face of concrete] x [rod diameter]
361 DOVETAIL SEISMIC ANCHOR: [gage] x 1 inch (25 mm) wide x [length
from face of concrete]
CHANNEL SLOT SYSTEM: Use versatile channel-slots
and anchors to attach masonry or stone veneer to new or existing masonry,
concrete, or steel structures or walls. Available in stainless, hot dipped
galvanized, Epoxy Coated, mill galvanized, or plain.
No. 130 WELD-ON CHANNEL SLOT: Weld to steel columns and beams
in the shop or field. 8" (203.2 mm) long x 1-3/8" (35mm) wide with a 9/16"
(14 mm) x 5-1/2" (140 mm) slot. Available in 16 gage or 11 gage. Specify
Steel Type. (Primer or plating may require touch-up at welds.)
No. 131 BUILT-IN CHANNEL SLOT: Build into new masonry walls.
Z-Anchors are welded to No. 130 Weld-On Channel Slots listed above. Specify
block size for length of Z-Anchors. Restraining bends in back are 1-1/2"
(38 mm) long. Specify Steel Type and Gage.
No. 132 SCREW-ON CHANNEL SLOT: Screw or bolt to existing masonry,
concrete, or steel. End tabs are 2" (51 mm) long 12" (305 mm) overall length).
Holes are 9/32" (14 mm) diameter for 1/4" (6.35 mm) fasteners. Available
in 11 gage or 16 gage. Specify Steel Type.
No. 133 LONG-TYPE CHANNEL SLOT: Build into new masonry walls
using channel slot anchors set into backup wall or attach to an existing
concrete or masonry wall using expansion anchors and bridge plate. Slots
are 7-3/8" (187 mm) long with 3/4" (19 mm) between each slot. 16 gage channel
slots are available in 5 ft. (1.524 m) lengths (7 slots) or 10 ft. (3.048
m) lengths (14 slots). Typical spacing is 16" (406 mm) o.c. Specify Steel
Type. Also available with optional holes between slots.
No. 133-P BRIDGE PLATE: Used to attach No. 133 Long Type Channel
Slots to existing walls. Made of 12 gage steel with 7/16" (11.1 mm) or
5/16" (7.9 mm) hole. Recommend minimum of 3 bridge plates for 5 ft. (1.524
m) channels or 5 bridge plates for 10 ft. (3.048 m) channels. Specify Steel
Type.
TO SPECIFY CHANNEL SLOT ANCHORS:
THICKNESS: 16 gage, 12 gage, and 1/8" (3.1 mm).
LENGTH: Measured from face of channel.
WIDTH: Channel-Slot anchors are 1-1/4" (31.75 mm) wide.
MATERIAL: Available in mill galvanized, hot dipped galvanized,
or stainless steel.
CHANNEL SLOT ANCHORS
122 CHANNEL SLOT PARTITION ANCHOR: [gage] x 1-1/4
inches (32 mm) x 12 inches (305 mm) from face of channel.
123 CHANNEL SLOT HORIZONTAL TRIANGLE ANCHOR: [gage] x 1-1/4 inches
(32 mm) x 12 inches (305 mm) from face of channel.
124 CHANNEL SLOT CAVITY WALL ANCHOR: [gage] x 1-1/4 inches
(32 mm) x 5 inches (127 mm) from face of channel.
125 CHANNEL SLOT FURRING ANCHOR: [gage] x 1-1/4 inches (32 mm)
x 1-1/2 inches (38 mm) from face of channel.
129 CHANNEL SLOT TRIANGULAR WIRE TIE: 12 gage clip factory assembled
to a 3/16 inch (4.76 mm) diameter x [tie length]
134 CHANNEL SLOT CORRUGATED ANCHORS: [gage] x 1-1/4 inches (32
mm) x [length] from face of channel.
135 CHANNEL SLOT STONE ANCHOR: [gage] x 1-1/4 inches (32 mm)
x [length] from face of channel x [i.d. length of bend].
136 CHANNEL SLOT SPLIT BEND ANCHOR: [gage] x 1-1/4 inches (32
mm) x [length] from face of channel x [i.d. length of split bend].
137 CHANNEL SLOT PIN ANCHOR: [gage] x 1-1/4 inches (32 mm) x
[length] from face of channel with [welded][fixed][loose] pin [diameter]
x [length] centered [length] from end of anchor [gage] x 1-1/4 inches (32
mm) x [length] from face of channel with [welded][fixed][loose] pin [diameter]
x [length] centered [length] from end of anchor
138 CHANNEL SLOT FLAT ANCHOR: [gage] x 1-1/4 inches (32 mm) x
[length] from face of channel
138-R CHANNEL SLOT THREADED ROD ANCHOR: [gage] x 1-1/4 inches
(32 mm) x [length] from face of channel x [rod diameter] [gage] x 1-1/4
inches (32 mm) x [length] from face of channel x [rod diameter]
362 CHANNEL SLOT SEISMIC ANCHOR: [gage] x 1-1/4 inches (32 mm)
wide x [length from face of channel].
Heckmann Building Products Inc.
1501 N. 31st Avenue
Melrose Park, IL 60160-2911
Toll-Free: (800) 621-4140
Tel: (708) 865-2403
Fax: (708) 865-2640
E-mail: heckmann@worldnet.att.net
Web site: www.heckmannbuildingprods.com