AMP-BOX All-Welded Box Lockers
Art Metal Products™
401 NW 12th Avenue, P.O. Box 4157
Deerfield Beach, FL 33442
Tel: (954) 429-9662
(800) 252-5633
Fax: (954) 429-9715
Product Description
Features common to Art Metal Products AMP-BOX All-Welded Box Lockers.
- All-Welded Unibody construction (side is integral to frame)
- 16 gauge diamond perforated sides
- 16 gauge solid top, bottom and shelves
- 18 gauge solid back
- 16 gauge full length piano hinge (Not on top hinged Box Lockers)
- All lockers prepared for both padlock and built-in locks (Locks available as an option)
Sizes for Box Lockers
Widths for all gym locker openings: 12", 15", 18"
Depths for all gym locker openings: 12", 16", 18", 22"
Four Tier
Opening Heights: 8", 9", 12", 15", 18"
Nominal Column Heights: 32", 36", 48", 60", 72"
Five Tier
Opening Height: 12"
Nominal Column Height: 60"
Six Tier
Opening Heights: 8", 10", 12"
Nominal Column Heights: 48", 60", 72"
Seven Tier
Opening Heights: (6) 10" & (1) 12" only
Nominal Column Height: 72"
Eight Tier
Opening Heights: 8", 9"
Nominal Column Heights: 64", 72"
Nine Tier
Opening Height: 8"
Nominal Column Height: 72"
Note: Actual column height 2-3/4" over nominal height.
AMP-BOX All-Welded Box Locker Specifications
PRODUCTS
MATERIALS
Steel Sheet: All sheet steel used in fabrication shall be prime grade free from scale and imperfections and capable of taking a heavy coat of high gloss baked enamel.
Stainless Steel: 304 stainless steel with no. 4 finish shall be used for all recessed handles and lock hole cover plates.
Fasteners: Zinc plated steel; bolt heads to be slotless type.
Equipment: Hooks and hang rods of zinc plated steel.
Number Plates: To be polished aluminum with not less than 3/8" high engraved numbers attached to door with two aluminum rivets. Numerals to be silver on black background.
FABRICATION
GENERAL: Lockers shall be Art Metal Products AMP-BOX ALL-WELDED BOX LOCKERS as manufactured by Art Metal Products. All lockers shall be factory-assembled, of all MIG welded construction, in multiple column units to meet job conditions. Assembly of locker bodies by means of bolts, screws, or rivets will not be permitted. Welding of knock-down locker construction is not acceptable. Grind exposed welds and metal edges flush and make safe to touch.
FINISHING: All surfaces shall be thoroughly cleaned with a seven stage hot-spray washing process and coated with an insoluble iron phosphate film to inhibit corrosion, followed by a coat of high grade enamel electrostatically sprayed and baked at 350 degrees Fahrenheit for a minimum of 20 minutes to provide a tough durable finish. Color to be selected from our 24 standard colors. Two-tone color combination (frame one color and the doors a second color) is available at no additional cost.
GYM DOORS (18" high and under): Shall be fabricated of single sheet prime 14 gauge steel with single bend at three sides and double bend at latch side. An 11 gauge spring loaded latch assembly shall be securely welded to the inside of the door. The latch shall be equipped with a stainless steel spring and shall automatically engage when door is closed. Rubber bumpers shall be riveted to return bends on doors. Locking device shall be designed for use with padlock or built-in lock. Doors 12" high and under shall be top hinged using a 3/16" diameter continuous hinge rod completely recessed into the door with a concealed fastener. Doors over 12" high shall be side hinged using a 16 gauge continuous piano type hinge, securely riveted to frame and welded to the door. Side hinging is optional for doors 12" high and under. Doors to be diamond perforated.
FRAME / VERTICAL SIDE PANELS: Shall be of integral frame and side wall construction manufactured from 16 gauge sheet steel. The frames shall be formed to provide a continuous door strike on the latch side. Sides are diamond perforated.
DOOR HINGES: See "Gym Doors" above.
INTEGRAL FRAME LOCKER BASE: 16 gauge formed sheet steel with double return flanges at the front and rear. A 16 gauge stiffening channel shall be MIG welded front-to-back at the bottom of each locker column.
FLAT TOPS: Shall be formed of one piece of 16 gauge cold rolled sheet steel as an integral part MIG welded to each vertical side panel frame member and be continuous to cover the full width of a multiple locker unit.
INTERMEDIATE SHELVES AND BOTTOMS: Shall be 16 gauge solid sheet steel, have double bends at front and shall MIG welded to the side.
BACKS: Shall be 18 gauge solid cold rolled sheet steel, be continuous to cover a multiple framed unit and welded to each vertical side panel.
LOCKER ACCESSORIES
LOCKS: Recommend Master #1670 (manual operating horizontal dead-bolt action). For padlocking, recommend Master #1525 combination padlock. Always order with a minimum of (5) Master / Control keys.
EQUIPMENT: None.
EXECUTION
INSTALLATION
GENERAL: Installation shall be in strict conformance with referenced standards, the manufacturer’s written directions, as shown on the drawings and as herein specified.
PLACEMENT: Units shall be set in place, plumb, level, rigid, flush and securely attached to the wall (or bolted together if back-to-back) and anchored to the floor or base according to manufacturer’s specifications.
ANCHORAGE: Anchor welded locker groups to floor/base 6" in from each locker unit end. Lockers shall be anchored to wall 6" from each locker unit end 6" above floor/base and 6" below unit top.
TRIM: Shall be installed using concealed fasteners. Provide flush, hairline joints against adjacent surfaces.
ADJUSTMENT
GENERAL: Upon completion of installation, inspect lockers and adjust as necessary for proper door operation. Touch-up scratches and abrasions to match original finish.
Available in all standard four thru nine tier welded locker sizes.
In the interest of safety, all Art Metal Products lockers must be securely anchored to the floor and/or wall.
Art Metal Products reserves the right to modify its design and/or to make changes in specifications or colors without prior notice.